[sadermo]

22.06.2011 CDMA day again, 3 new models supported


Whats new:

• Motorola W200 full support
• Huawei C2801 full support
• Nokia 1006 full support

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

Dont forget to check previous updates :

RIFF JTAG – HTC Desire HD A9191 (HTC Ace) Unbrick, IMEI, CID, ModelID, Simlock repair « RIFF Box – JTAG Revolution,

RIFF JTAG – JTAG Manager v1.33, RIFF Box firmware v1.25 released « RIFF Box – JTAG Revolution


RIFF Box – JTAG Revolution

[sadermo]

22.06.2011 Samsung Galaxy S 4G (T959v 1GB) Unbrick – Boot repair supported
Samsung T959V is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in very rare cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.
To resurrect Samsung T959V:

• Solder JTAG cable to Samsung T959V JTAG pads;
• Connect microUSB cable to phone and PC;
• Insert battery;
• Make sure Samsung T959V is selected in the list of models;
• Make sure a fixed TCK frequency is selected;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold both ‘Volume Down’ and ‘Volume Up’ keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[sadermo]

RIFF JTAG – HTC Wildfire S A510E (HTC Marvel), More CDMA models supported



07.07.2011 HTC Wildfire S A510E (HTC Marvel), More CDMA models supported.
Resurrecting HTC WildFireS is easy. Phone is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
In case you have no USB cable near, make sure battery is charged enough and hold Power On button during initiation of JTAG connection.
Resurrector will reflash radio’s boot zone and will re-write PDA’s SPL to 1.01.0002 version. Additionally to SPL and Radio zones, the zone which contains Model ID is re-flashed too. Thus after resurrection phone will have Model ID = ‘PC4910000′. Additionally, you can check ‘Repair RECOVERY zones’ to reflash android BOOT and RECOVERY code.
To resurrect HTC WildFireS:

• Solder JTAG cable to HTC WildFireS JTAG pads;
• Insert USB Data cable into board and PC;
• Make sure HTC WildFireS is selected in the list of models;
• If you use battery, press Power On key;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold ‘Volume Down’ key and press ‘Power ON’ button. In few seconds you should see usual android boot mode screen.

Following CDMA models are supported from today :

• Samsung B139 Repair/Unbrick, Read/Write NOR Flash
• Samsung B259 Repair/Unbrick, Read/Write NOR Flash
• Samsung B309 Repair/Unbrick, Read/Write NOR Flash
• Samsung B319 Repair/Unbrick, Read/Write NOR Flash
• Samsung B379 Repair/Unbrick, Read/Write NOR Flash
• Samsung B619 Repair/Unbrick, Read/Write NOR Flash
• Huawei C31 Repair, Read/Write NOR flash

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[sadermo]

RIFF JTAG – Samsung T749, Samsung E189 Unbrick – Boot repair supported



12.07.2011 Samsung T749, Samsung E189 Unbrick – Boot repair supported

The Samsung T749 board is auto powered on with USB Data Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
To resurrect Samsung T749:

• Solder JTAG cable to Samsung T749 JTAG pads;
• Connect USB cable;
• Make sure Samsung T749 is selected in the list of models;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect power supply, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using known flashing methods.
In case you cannot find firmware files use Global RIFF Link & Data Exchange plugin – at the moment of resurrector release there was shared full dump from alive Samsung T749 phone.
To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold both ‘Volume Up’ and ‘Camera’ keys and press ‘Power ON’ button.

Resurrecting Samsung E189 is simple.
Phone is auto powered on with USB Cable connected to the PC. Battery presence is not required; connection can be established with detached board.
Current resurrector contains Firmware and EEPROM zones for memory chip with ID 0x00EC/0×2256
To resurrect Samsung E189:

• Solder JTAG cable to Samsung E189 JTAG pads;
• Insert USB Data cable into board and PC;
• Make sure Samsung E189 is selected in the list of models;
• Click Resurrect button;
• Choose which areas to flash;
• Wait till software signals a successful operation completion;
• De-solder JTAG wires;

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[sadermo]

Here is short list of latest news :

RIFF JTAG – Qtek 9000 (HTC Universal) Unbrick – Boot repair supported « RIFF Box – JTAG Revolution

Other names for this device :

• I-Mate JASJAR (HTC Universal)
  
  
• Dopod 900 (HTC Universal)
  
  
• O2 XDA Exec (HTC Universal)
  
  
• T-Mobile MDA Pro (HTC Universal)
  
  
• Orange SPV M5000 (HTC Universal)
  
  
• Qtek 9000 (HTC Universal)
  
  
• Grundig GR980 (HTC Universal)
  
  
• Vodafone VPA IV / v1640 (HTC Universal)
  
  

Bug fix updates :

• HTC_Wildfire.dll
  
  - Added feature to flash RECOVERY and BOOT zones during resurrection.
  - Added code reading option
• HTC_WildfireS.dll
  - By mistake was released DLL for usual HTC Wildfire model. Now is ok.
  
  Thanks to Tatek and Basar for help. Free beers for both

Qualcomm Partition tool 1.04 :

• Added support for 4kb page code reading (Applies to HTC Models)

In case You want to read unlock code from dump with 4kb page, and You get "Simlock zone is not found" message, tick "Don't adjust HTC Partition for 4kb NAND pages" check box, and read partition again.

Beta testers required for Samsung Galaxy S II :

Samsung Galaxy S2 i9100 wanted for beta test ! ! !

Support for Exynos 4210 Samsung CPU is added, and will be released after tests.


Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

[sadermo]

RIFF JTAG – Samsung I9100 Galaxy S II Unbrick – Boot repair supported, World First ! ! !



29.07.2011 Samsung I9100 Galaxy S II Unbrick – Boot repair supported, World First ! ! !
Samsung I9100 is based on the S5PV310 (Exynos 4210) Processor (Cortex-A9 Dual-Core).
JTAG pads are very small; professional experience in soldering is required to connect wires to the JTAG interface. There is a big variety of versions of Galaxy II devices: GT-I9100, GT-I9100G, GT-I9100L, GT-I9100M, GT-I9100T, GT-I9101, GT-I9103, GT-I9108, GT-I9188, and maybe more. Some of them are based on different hardware platform – the OMAP4430 (Cortex-A9 Dual-Core). Thus make sure first which exact hardware version you have on hands.
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on.
Phone has such booting sequence: ROM → FBL → IBL → PBL → SBL. Current resurrector will resurrect Partition Table (PIT) and SBL zones which are located in the iNAND (eMMC) memory. Write access to memory which contains FBL, IBL and PBL loaders is not supported currently, but in case your phone has these loaders damaged, you can choose “Initiate Download Mode” way of resurrection in order to directly put the phone into the Download Mode.
To resurrect Samsung I9100:

• Solder JTAG cable to Samsung I9100 JTAG pads;
• Connect USB cable to phone and PC;
• Insert battery;
• Make sure Samsung I9100 is selected in the list of models;
• Make sure a fixed TCK frequency is selected;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.
To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[sadermo]

02.08.2011 RIFF JTAG - SonyEricsson Xperia X8, X10 Mini supported

Whats new today :

• SonyEricsson Xperia X8/E15 Unbrick, Boot repair, and NAND Chip Backup/Restore
• SonnyEricsson Xperia X10a Mini /E10 Unbrick, Boot repair, and NAND Chip Backup/Restore
• USB Broadband Modem ZTE MF627 new CPU ID added to allowed list

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.


RIFF Box – JTAG Revolution

[sadermo]

03.08.2011 Samsung Galaxy Tab M180s Unbrick – Boot Repair supported


Samsung M180S is based on the S5PCxxx Processor (ARM core is Cortex-A8).
Note, one simple way to connect over JTAG – connect USB cable to PC and insert battery. In this case phone is automatically powered on. But note, in some cases it is possible that you will have to hold Power On key during initial connection.
In case after resurrection (after you have tried with both boot versions) the download mode is not initiated (LCD remains blank) do repeat resurrection with ‘Clone Gremlin zone’ option checked.


To resurrect Samsung M180S:

• Solder JTAG cable to Samsung M180S JTAG pads;
• Connect USB cable to phone and PC;
• Attach battery connector;
• Make sure Samsung M180S is selected in the list of models;
• Make sure a fixed TCK frequency is selected;
• Click Resurrect button;
• Wait till software signals a successful operation completion;
• Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold both ‘Volume Down’ and ‘Home’ keys and press Power-On.

Please click “Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

[sadermo]

RIFF JTAG - Samsung Galaxy GIO (S5660) Unbrick - Boot repair supported 23.08.2011 Samsung Galaxy GIO (S5660) Unbrick – Boot repair supported


Samsung S5660 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.


To resurrect Samsung S5660 do this:

• Solder JTAG cable to Samsung S5660 JTAG pads;
• Insert battery and connect USB cable to phone and PC;
• Make sure Samsung S5660 is selected in the list of models;
• Click Resurrect button;
• Wait few seconds until software signals a successful operation completion;
• Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold both ‘Volume Down’ and ‘OK’ keys and press Power-On to enter Download Mode;

Please click “ Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution

[sadermo]

RIFF JTAG - Samsung Galaxy GIO (S5660) Unbrick - Boot repair supported
23.08.2011 Samsung Galaxy GIO (S5660) Unbrick – Boot repair supported


Samsung S5660 resurrection is simple. Phone is auto powered when USB Data Cable is inserted while battery is inside. If you don’t use USB cable, make sure to hold Power On button during JTAG connection establishing phase.


To resurrect Samsung S5660 do this:

• Solder JTAG cable to Samsung S5660 JTAG pads;
• Insert battery and connect USB cable to phone and PC;
• Make sure Samsung S5660 is selected in the list of models;
• Click Resurrect button;
• Wait few seconds until software signals a successful operation completion;
• Disconnect USB cable, de-solder JTAG wires;

Now phone is in bootable condition, that is, even if it does not start up normally, you can flash it using original Samsung downloader software to restore it to the working state.


To enter download mode:

• Disconnect PC cable;
• Insert battery;
• Hold both ‘Volume Down’ and ‘OK’ keys and press Power-On to enter Download Mode;

Please click “ Check For Updates” button in order to download and apply new files. Closing all running application before starting update process is recommended.

RIFF Box – JTAG Revolution